Are you looking for a step by step guide to clean Dyson Vacuum? Let’s talk about that.
Vacuums are an essential part of cleaning a home, but did you know you need to regularly clean your vacuum?
Without cleaning your Dyson vacuum regularly, you risk the performance of the vacuum, which can ultimately result in its shortened lifespan.
Not many people know that vacuums can last up to 8 years with good care. If you don’t care for your vacuum and clean it often, then it will likely only last a matter of several years.
So, if you’re wondering the best way to clean your Dyson vacuum, you’ve come to the right place. Here is our guide on how to clean a Dyson vacuum!
How To Clean Dyson Vacuum – A Step-By-Step Guide
You will need:
- Water
- Dish soap
- Paper towels
- Scissors/Knife
- Air compressor/Can of compressed air
- Flathead screwdriver
Before you start these steps, make sure to only complete this cleaning process outdoors.
Cleaning a Dyson vacuum can be a surprisingly messy task, so you don’t want to ruin the quality of your floor inside!
Also, this goes without saying, but make sure the vacuum is turned off and unplugged at the socket.
This method calls for using water on an electrical object, which we all know isn’t an ideal combination when the electronic object is turned on.
Step 1 – Empty The Canister
Firstly, you’ll need to empty the canister. To do this, you’ll need to press the button at the back of the vacuum to open the outer canister shell.
This button is typically red and located at the back of the vacuum, and when pressed, it will open the outer canister shell for you to remove the canister inside.
Once removed, empty the canister of any debris, dust, hair, and anything that’s inside.
It’s easiest to empty this into a plastic bag before putting it in the trash can, otherwise you risk inhaling bits of dust and debris.
Step 2 – Take Out The Foam Filter
Then, open the bottom flap to reveal the foam filter.
This is a flat, circular filter that is located at the top of the vacuum part, and at the bottom of the hose.
Take the foam filter out and leave it on the side for later.
Step 3 – Clean The Roller
Now, turn the vacuum upside down. Take the flathead screwdriver and remove the bottom roller cover, which should be a transparent plastic covering the roller brush inside the vacuum.
Make sure to put the screws in a safe place, such as a Tupperware box, to avoid losing them.
Now, you need to clean the roller. To do this, use a pair of scissors or a knife to cut free tangled pieces of hair and debris that might be stuck around the roller. Pull everything out so the roller is clean.
Even if the roller looks completely clean, you’ll need to use an air compressor (or can of compressed air) to blow away any dust or small particles that might be lingering in the roller’s bearings.
More dust will fly out than you might expect, so it might be worth covering your mouth and eyes with your t-shirt.
Once completely clean, screw the bottom roller cover back on.
Step 4 – Clean The Cyclone
Now’s time to clean the main function of your vacuum – the cyclone. To clean the cyclone, you need to remove it and hold it over a trash can.
Then, clean it with your air compressor in every single part – including the little holes. Make sure to turn it over and clean the inside, too.
This is arguably the messiest part of cleaning a Dyson vacuum, which is why we recommend doing it over a trash can.
f you have sensitive skin or breathing problems, make sure to cover your nose and mouth with a mask or t-shirt.
Step 5 – Clean The Canister
The first step to cleaning the canister is to blow away any lingering dust or debris particles with the air compressor.
Then, you need to scrub it down with a sponge, dish soap, and warm water. You can either do this outside with a bucket of warm, soapy water or move the vacuum parts inside.
If there are any tough stains, you can use a more abrasive cleaning tool like an old toothbrush – which is also handy for getting the small corners.
Step 6 – Clean The Foam Filter
Bring the foam filter under a tap and run it underneath the water until the water runs clear. Make sure to squeeze the filter regularly to make sure all the dirt is being washed away.
Step 7 – Clean The Head
The head doesn’t need to get too wet, so just make sure to wipe it down with a damp cloth and ensure that every hole is empty rather than clogged.
Dyson recommends against running the head under running water, so avoid doing this and stick to wiping.
Step 8 – Clear The Hose
Make sure the hose is completely clear from debris, such as hair or small objects, to prevent blockages from occurring.
You can use the air compressor for this, or try to stick something long and pointy down the hose.
Step 9 – Dry The Parts
Finally, you need to allow time for the parts to dry.
This is because leaving any form of moisture or dampness inside the vacuum will lead to damp and mold, and will also encourage dirt and debris to get stuck in the holes of the cyclone and canister.
We recommend leaving all the parts out to dry outdoors on a dry day, and leave them to dry completely overnight. Once dry, you can reassemble the parts of the vacuum.
You might need to replace the foam filter entirely, as it should be replaced once every 3 months.
However, with regular cleaning, you can extend its service life by an extra month.
Conclusion
So, there you have it! It turns out, cleaning a Dyson vacuum is a straightforward task.
Just make sure to commit to cleaning your Dyson vacuum every few months to ensure the vacuum is working properly.