How To Clean Your Dyson Filter V10

Do you need tips to follow when you plan to clean your Dyson filter? We got you covered.

We don’t need to tell you how good Dyson vacuum cleaners are, and the V10 series of the V range is perhaps one of the best of the bunch, so excellent choice!

A V10 should provide exquisite performance over the course of an exceptionally long service life, but only if you take good care of it.

In order to keep your V10 beast, well… beastly, you’ll need to keep up with maintenance, which sounds like a drag, but really, all that means is that you’ll have to clean or replace the filter from time to time.

Even better, once you know how it’s done, the filter cleaning process couldn’t be easier, and we’re going to break it down for you in our step-by-step guide.

The full process takes roughly 24 hours, so read on and get started to get your vacuum up and running again ASAP.

What You’ll Need To Clean Your Dyson Filter

Dyson likes to keep it simple when it comes to filter maintenance, and it’s a customer-kind approach that we both respect and appreciate.

You won’t need to make any aftermarket purchases to complete any of the steps in our guide. Nothing special is required.

All you’ll need is…

  • The filter

How To Clean Your Dyson Filter V10

  • Clean and cold running water
  • A rigid surface (your sink will do just fine)
  • A safe, warm, well ventilated place

… Basically, if you have a cold water faucet, you’re good to go, so without further ado, let’s get cleaning!

Cleaning Your V10 Dyson Filter

Unlike the V7 and V8 series, the Dyson V10 series, along with its more powerful siblings in the V11 and V15 series, utilizes only one filter as opposed to separate pre and post filters.

This means that your job is even easier, as you only have to locate and clean a single unit — lucky you!

If you need help cleaning your V8 filters, we got you covered as well!

Here’s how it’s done.

Turning Off Your Dyson V10

First thing’s first; make sure your vacuum is powered down. This may seem like an obvious step, but you’d be surprised how easy it is to forget to shut a vacuum off before getting started, and this can potentially damage both the filter and the vacuum itself.

As the V10 series is composed of cordless units exclusively, you don’t have to worry about switching off outlets but do ensure that the cable connecting it to the charging port is disconnected.

Don’t worry about turning the vacuum itself off either, as V10 series hoovers are only activated when the trigger is pulled. Avoid the trigger, and, technically, it’s powered down.

Once you’re ready to move on to the next step, remove the wand section of the hoover and place the remaining machine on a stable, flat surface.

Locating & Removing The V10 Filter

Now’s the time to locate that filter of yours and extract it from the vacuum. On all V10, V11, and V15 units, the filter can be found in the same place.

It will be integrated into the cylindrical enclosure above the handle and trigger.

Secured in place by a latching system, you can’t simply pull it from the main enclosure. Instead, firmly grasp the end of the cylinder, and turn it clockwise gently.

You don’t need to put too much mustard on it; a slight turn roughly two inches to the left should uncouple the filter. Then you can pull it free from the machine.

How To Clean Your Dyson Filter V10

Washing The Filter

Take your newly recovered filter and head to a sink of your choice. You could also use an exterior faucet if need be. As long as it runs cold, it should be fine.

Before you get rinsing, grab your filter and tap it on a rigid surface to try and knock loose some of the bulkier debris, as this will speed up the cleaning process a great deal.

You should tap firmly, but not so hard that you’ll damage the enclosure of the filter or that the vibrations will damage the interior plastic.

Once you’ve tapped as much debris loose as you can, turn on the faucet, and run the cold water through the filter and against all its surfaces.

Every 10 seconds or so, tap the filter on a hard surface to try and remove more detritus. Repeat this two-stage process until the water draining from the filter runs clear.

Drying The Filter

Drying your filter is the easiest yet longest step on the path to a fully functioning Dyson V10. Simply pick out a safe spot to place it to air dry.

This spot should be relatively warm, with decent airflow to facilitate a quick drying process.

In optimal conditions, your V10 filter should be fully dry after a 24-hour waiting period.

Reassembly

Sure your filter is completely dry? Fantastic, all you need to do now is install it back into the vacuum by placing it flush against the connective zone and turning clockwise gently until you hear an affirmative click, and voilà; job done!

To maximize your cleaning routine, we also recommend emptying your V10 at the same time.

How Often Should You Clean Your Dyson Filter V10?

If you hoover often or have more ground to cover, we’d recommend cleaning your filters once a month, but for a less intensive schedule, you can get away with once every 3 months.

How Often Should You Replace Your Dyson Filter V10?

Again, if you vacuum a lot, you’ll have to replace your filters more frequently. For intensive cleaning, replacing parts every 3 months will ensure that your V10 stays in top condition.

For more relaxed cleaning schedules, changing the filter once a year will suffice.

If you’re looking for value for money from your filter replacement, we’d suggest taking a quick look at this one from Leadaybetter.

Vacuum Filter Replacements for Dyson V10 Cyclone Series, V10 Animal, V10 Absolute, V10 Total Clean, SV12, Part No. 969082-01 (2 Pack Filters and 1 Clean Brush)

Final Thoughts

There you have it — a comprehensive guide to keeping your filter squeaky clean and your Dyson V10 ferocious!

Remember to keep track of how long you’ve been using your filter and how many times you’ve cleaned it, as its performance will eventually start to dip, no matter how well you care for it.

Once this happens, source a replacement, and hoover on!

Leave a Comment